1. Remove the battery for 10 seconds.
2. Press and hold one of the buttons on the hand transmitter and re-insert the battery (and the battery cover for the HS1 BS / HS4 BS/ HS5 BS).
Read More…
Info Sheet: ABi011.1 – Transfering the code from an existing HSE 4 BiSecur transmitter to a new BiSecur transmitter
Series 3 Hand Transmitters
Please note: To transfer the code from one hand transmitter to another, the signal strength needs to be very strong. This means the units need to be very close together and have a good battery power.
The procedure is more reliable if the receiving transmitter is on the left hand side, ideally in direct contact with the sending / existing transmitter, with their tops level (see image below).
Read More…
Info Sheet: ABi019 – How to set up the Hörmann CTV 1 and CTV3 Digital Keypads
The Hörmann CTV keypads are digital external keypads that allow a user to open and close their garage door (or any device that accepts a volt free relay impulse) using a 3 – 5 digit pin number.
The CTV1 has a single relay output and can control a single device and the CTV3 has 3 relay outputs, although only 2 can be used as direct control relays with the third relay providing additional options for the Hörmann automation systems. In this article we will focus on the direct control aspect of the devices and demonstrate setting up the units to open and close your garage door. Both the CTV1 and CTV3 are supplied with an external keypad and an internal control unit. The external keypad comes complete with a fixed cable of 5m. This can be shortened or extended up to 20m.
Read More…
Info Sheet: ABi011 – Transfering the code from an existing BiSecur transmitter to a new BiSecur transmitter
Series 3 Hand Transmitters
Please note: To transfer the code from one hand transmitter to another, the signal strength needs to be very strong. This means the units need to be very close together and have a good battery power.
Read More…
Info Sheet: ABi010 – Transferring Codes From a Hormann 868.3MHz Series 2 HSE2 to a Bisecur Transmitter
Hormann Series 2 / Series 3 Hand Transmitters.
Please note: To transfer the code from one hand transmitter to another, the signal strength needs to be very strong. This means the units need to be very close together and have a good battery power.
Read More…
Info Sheet: ABi007 – Erasing Codes From a Hormann Supramatic Operator
Supramatic BiSecur Series 3
1. Press and hold the ‘PRG’ button until the menu displays ’00’
2. Press and release the up arrow to move up through the menu until you reach menu ’40’
3. Now press and hold down the PRG button – ’40’ will start to flash then flash quicker with a dot in the bottom right ’40.’
Read More…
Info Sheet: ABi006 – How to code in a hand transmitter to the Hormann BiSecur Supramatic operator
1. Press and hold the ‘PRG’ button untill ’00’ is displayed.
2. Press and release the ‘UP’ arrow twice until ’11’ is displayed.
3. Press and hold the ‘PRG’ button untill ’11’ starts flashing.
Read More…
Info Sheet: ABi014 – Resetting the Hormann RollMatic Series 2 and 3 Roller Garage Door Operator
1. Disconnect the unit from the mains power supply.
2. Press and hold the ‘T’ button whilst plugging the unit back into the mains.
The courtesy light will flash once and the red light around the ‘T’ button will start to flash, you can now release the button.
Read More…
Info Sheet: ABi009 – Manual and Automatic Operation of Hormann Operators
To disconnect the door from the operator (operate the door manually)
Pull on the cord attached to the cage that travels along the boom arm. It will click out of the belt and allow the door to be opened and closed manually.
Read More…
Info Sheet: ABi008 – Resetting the Hormann BiSecur Supramatic Series 3 Operator
Please note: Make sure the emergency release is not engaged and the door is set to work automatically.
1. Disconnect or switch off the mains plug, and also the plug for the emergency battery if one is connected.
Read More…
On site with @abigaragedoors fitting one of our new ART sectional garage doors.
#Hörmann #StaySafe #photo #garagedoors
