Other Pages

Your local Garage Door and remote control specialist
Local Rate Number
t: 0330 660 1022
Menu

Category Archives: Garage Door How To Guides

Transfering the code to a Hormann HSE 4 BS hand transmitter

Hormann HSE 4 BS Transfer Code Instructions

Info Sheet: ABi011.1 – Transfering the code from an existing HSE 4 BiSecur transmitter to a new BiSecur transmitter
Series 3 Hand Transmitters

Please note: To transfer the code from one hand transmitter to another, the signal strength needs to be very strong. This means the units need to be very close together and have a good battery power.

The procedure is more reliable if the receiving transmitter is on the left hand side, ideally in direct contact with the sending / existing transmitter, with their tops level (see image below).
Read More…

Transfering the code from an existing BiSecur transmitter to a new BiSecur transmitter

Transfering the code from an existing BiSecur transmitter to a new BiSecur transmitter

Info Sheet: ABi011 – Transfering the code from an existing BiSecur transmitter to a new BiSecur transmitter
Series 3 Hand Transmitters

Please note: To transfer the code from one hand transmitter to another, the signal strength needs to be very strong. This means the units need to be very close together and have a good battery power.
Read More…

Transferring Codes From a Hormann 868.3MHz Series 2 HSE2 to a Bisecur Transmitter

Transferring codes from a Hormann 868.3MHz series 2 HSE2 to a Bisecur transmitter

Info Sheet: ABi010 – Transferring Codes From a Hormann 868.3MHz Series 2 HSE2 to a Bisecur Transmitter
Hormann Series 2 / Series 3 Hand Transmitters.

Please note: To transfer the code from one hand transmitter to another, the signal strength needs to be very strong. This means the units need to be very close together and have a good battery power.
Read More…

Erasing codes From a Hormann Supramatic Operator

Erasing codes from a Hormann Supramatic Operator

Info Sheet: ABi007 – Erasing Codes From a Hormann Supramatic Operator
Supramatic BiSecur Series 3

1. Press and hold the ‘PRG’ button until the menu displays ’00’

2. Press and release the up arrow to move up through the menu until you reach menu ’40’

3. Now press and hold down the PRG button – ’40’ will start to flash then flash quicker with a dot in the bottom right ’40.’
Read More…

How to code in a hand transmitter to the Hormann BiSecur Supramatic Series 3 operator

How to code in a hand transmitter to the Hormann BiSecur Supramatic operator

Info Sheet: ABi006 – How to code in a hand transmitter to the Hormann BiSecur Supramatic operator

1. Press and hold the ‘PRG’ button untill ’00’ is displayed.

2. Press and release the ‘UP’ arrow twice until ’11’ is displayed.

3. Press and hold the ‘PRG’ button untill ’11’ starts flashing.
Read More…

Resetting the Hormann RollMatic Series 2 and 3 Roller Garage Door Operator

Resetting the Hormann RollMatic Series 2 and 3 Roller Garage Door Operator

Info Sheet: ABi014 – Resetting the Hormann RollMatic Series 2 and 3 Roller Garage Door Operator

1. Disconnect the unit from the mains power supply.

2. Press and hold the ‘T’ button whilst plugging the unit back into the mains.

The courtesy light will flash once and the red light around the ‘T’ button will start to flash, you can now release the button.
Read More…

Manual and Automatic Operation of Hormann Operators

Hormann Manual Automatic Operation

Info Sheet: ABi009 – Manual and Automatic Operation of Hormann Operators

To disconnect the door from the operator (operate the door manually)

Pull on the cord attached to the cage that travels along the boom arm. It will click out of the belt and allow the door to be opened and closed manually.
Read More…

Resetting the Hormann BiSecur Supramatic Series 3 Operator

Hormann BiSecur Series 3 Operator Reset

Info Sheet: ABi008 – Resetting the Hormann BiSecur Supramatic Series 3 Operator

Please note: Make sure the emergency release is not engaged and the door is set to work automatically.

1. Disconnect or switch off the mains plug, and also the plug for the emergency battery if one is connected.
Read More…

Resetting the Hormann Supramatic Series 2 Operator

Hormann Supramatic Series 2 Reset

Info Sheet: ABi001 – Resetting the Hormann Supramatic Series 2 Operator.

Please note: Make sure the emergency release is not engaged and the door is set to work automatically.

1. Turn on the mains power supply to the unit while holding down the ‘PRG’ button. Keep the ‘PRG’ button pressed untill the screen shows ‘C’.

2. Release the ‘PRG’ button and the display briefly shows ‘J’ then a slowly flashing ‘0.’.
Read More…

Categories